Delta Tau ACC-24E2S Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 45

background image

Accessory 24E2S

Ultralite/MACRO Station Setup

20

ULTRALITE/MACRO STATION SETUP

The Acc-24E2 family of JEXP accessories also can be used with MACRO Station to breakout the
standard amplifier, flag, and encoder signals. The gate arrays on the Acc-24E2 family of accessories are
located in the traditional channel 9-16 locations of the PMAC2 memory map.

Note:

In order for the MACRO Station to setup its output and input channels
automatically, MACRO Station firmware 1.114 or greater must be used.

Currently there are three types of Acc-24Es to be used with the MACRO Station:

Acc-24E2

Direct PWM commutation outputs

Acc-24E2A



10V Outputs for torque, velocity and sinusoidal input amplifiers

Acc-24E2S

Dedicated 4-channel stepper interface card

MACRO Station Gate Array Locations for Acc-24E2

Chan #

9

10

11

12

13

14

15

16

Hex

[$C040]

[$C048]

[$C050]

[$C058]

[$C060]

[$C068]

[$C070]

[$C078]

Hardware Setup for MACRO Station Use

A few hardware selections must be set in order to use this accessory with the MACRO Station:

E5

Jumper 1-2 for MACRO or Turbo communications (603804-105 and above)

E16

Jumper 1-2 for Clock Settings

SW1

SW1-1 and SW1-2 both on for $C040, both off for $C060 SW1-3 through SW1-6 set to off

Node-Specific Gate Array MI-variables

MI-variables MI910 through MI919 on the MACRO station control the hardware setup of the hardware
interface channel on the station associated a MACRO node. The matching of hardware interface channels
to MACRO nodes is determined by the setting of the SW1 rotary switch on the CPU/Interface Board of
the MACRO station.

These variables are accessed using the MS station auxiliary read and write commands. The number
immediately after the MS specifies the node number, and therefore the channel number mapped to that
node by the SW1 setting.

Encoder/Timer n Decode Control (MSn,MI910)

MI910 controls how the input signal for the encoder mapped to the specified node is decoded into counts.
As such, this defines the sign and magnitude of a count. The following settings may be used to decode an
input signal.

0:

Pulse and direction CW

1:

x1 quadrature decode CW

2:

x2 quadrature decode CW

3:

x4 quadrature decode CW

4:

Pulse and direction CCW

5:

x1 quadrature decode CCW

6:

x2 quadrature decode CCW

7:

x4 quadrature decode CCW

8:

Internal pulse and direction

9:

Not used

10:

Not used

«
...
21
22
23
24
25
...
»

Содержание ACC-24E2S














































Отзывы:

Нет отзывов

Похожие инструкции для ACC-24E2S

C50FSi - VB Network Camera

Бренд: Canon Страницы: 32

Бренд: Rabbit Страницы: 120

Бренд: TC Electronic Страницы: 2

Бренд: Data Translation Страницы: 98

Network Video Recorders

Бренд: e-Line Technology Страницы: 34

Бренд: Omnia Страницы: 6

Бренд: X-Micro Страницы: 9

Бренд: X-Micro Страницы: 19

CLICK PLUS C2-02CPU

Бренд: Automationdirect.com Страницы: 10

Бренд: SIIG Страницы: 12

PG-FlexPlus AMU-912

Бренд: ADC Страницы: 130

Бренд: Fieldbus Specialists Страницы: 39

Бренд: Lanner Страницы: 63

Бренд: Campbell Страницы: 38

Converter Board R0E5212BACFG00

Бренд: Renesas Страницы: 6

Бренд: TANDBERG Страницы: 3

4 Channel Input Buffer Board SDAIBB

Бренд: B&B Electronics Страницы: 22

Бренд: Alcatel-Lucent Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды