manualshive.com logo in svg

Delta Electronics Network Device IFD9506, Руководство по эксплуатации

Поделиться
Скачать
Delta Electronics Network Device IFD9506 Скачать руководство пользователя страница 3

Ethernet Communication Module IFD9506

 

DVP-PLC Operation Manual

 

1 

 

Warning 

 Please read this instruction carefully before use and follow this instruction to operate the device in order to 

prevent damages on the device or injuries to staff.   

 Switch off the power before wiring. 

 IFD9506 is an OPEN TYPE device and therefore should be installed in an enclosure free of airborne dust, 

humidity, electric shock and vibration. The enclosure should prevent non-maintenance staff from 
operating the device (e.g. key or specific tools are required for operating the enclosure) in case danger 
and damage on the device may occur. 

 IFD9506 is to be used for controlling the operating machine and equipment. In order not to damage it, 

only qualified professional staff familiar with the structure and operation of IFD9506 can install, operate, 
wire and maintain it.   

 DO NOT connect input AC power supply to any of the I/O terminals; otherwise serious damage may occur. 

Check all the wirings again before switching on the power and DO NOT touch any terminal when the 
power is switched on. Make sure the ground terminal    is correctly grounded in order to prevent 
electromagnetic interference. 

 

 

Table of Contents

 

1  Introduction ........................................................................................................................................ 4 

1.1  Features ........................................................................................................................................... 4 
1.2  Installation and Wiring ...................................................................................................................... 4 
1.3  Specifications ................................................................................................................................... 5 

2  Product Profile & Outline ................................................................................................................... 7 

2.1  Dimension ........................................................................................................................................ 7 
2.2  Product Profiles ................................................................................................................................ 7 
2.3  LED Indicators.................................................................................................................................. 7 
2.4  Indicator Display and Error Warning ................................................................................................. 7 
2.5  RJ-11 Pin Definition .......................................................................................................................... 9 
2.6  RJ-45 Pin Definition ......................................................................................................................... 9 
2.7  RS-232 Pin Definition ....................................................................................................................... 9 
2.8  Node Address .................................................................................................................................. 9 
2.9  Data Format and Baud Rate ........................................................................................................... 10 
2.10 Feed-through Terminal Pin Definition ............................................................................................. 11 

3  MODBUS Communication ............................................................................................................... 12 

3.1  Modbus Function Codes Supported ............................................................................................... 12 
3.2  Registers in IFD9506 and Modbus Addresses ................................................................................ 12 
3.3  Table of Basic Registers (BR) ......................................................................................................... 12 

Содержание Network Device IFD9506

































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды