- 10 -
- 11 -
Personalising the installation and the products
4
The CLT 8000 TYXAL+ touch screen keypad allows all the personalisation operations of the system.
The following menus can be accessed by the installer code.
The CLT 8000 TYXAL+ touch screen keypad can be used for all activation actions.
Deactivate the tamper alarm (see § Deactivating the tamper alarm, system guide) and separate it
from its wall mount.
Example: DMB TYXAL+ motion detector
• Name the products
❶
Enter the installer code (123456, by default) and confi rm with OK.
❷
Press
Settings
, select the menu:
Installation > Products > Confi gure,
then confi rm with OK.
❸
Press the button of the product to rename or select it
from the list of products by clicking on
"Browse"
(see table below)
,
then confi rm with OK.
❹
Once the product is identifi ed, select the
"Name"
menu, then confi rm with OK.
❺
You can choose a name from the list
(recommended), then a number (optional)
or
personalise (
❻
) the product name by entering a new name.
Confi rm with OK.
• Entry timer on intrusion detectors (immediate/delayed triggering)
❶
Enter the installer code (123456, by default) and confi rm with OK.
❷
Press
Settings
, select the menu:
Installation > Products > Confi gure,
then confi rm with OK.
❸
Press the button of the product to change or select it
from the list of products by clicking on
"Browse",
then confi rm with OK.
❹
Once the product is identifi ed, select the
"Entry timer"
menu, then confi rm with OK.
❺
Select the type of triggering:
immediate or delayed (5 to 45 seconds)
,
then confi rm with OK.
Immediate:
if a presence is detected, the alarm is immediately
triggered.
Delayed:
if a presence is detected, the alarm is triggered after a
delay (set from 5 to 45 seconds) to give the user time to deac-
tivate the alarm, after entering the building (e.g. activation or
deactivation with a wall-mounted touch screen keypad).
During this time, the alarm control unit emits warning beeps.
abc
def
jkl
ghi
mno
tuv
pqrs
wxyz
25/11/15
12:48
SOS
Réglages
OFF
4
5
Entrance timer
Immediate >
Ok
Return
DMB 0 AD AD
Ok
Return
Tamper alarm
Name
Entrance timer
Entrance timer
< 5 s
>
Ok
Return
Entrance timer
< 45 s
>
Ok
Return
Installation
Zones
Door chime
Ok
Products
Return
OR
Name
Ok
Bedroom
Child's bedrm
Master bedrm
Return
Configure
Browse
Return
product
Press the button of the
Products
Ok
Activate/deactivate
Return
Add
Configure
Name
Reception
Alley
Personalise
Return
PSTN transmitter
Ok
Return
Tamper alarm
Entrance timer
Name
4
5
6
Settings
Clock
Languages
Ok
Return
Installation
Ok
Access code
XXXXX
X
Ok
SOS
or Browse
Configure
Ok
Return
CLT 0 54 22
DMB 0 AD AD
1
3
2
RTC 0 03 01
Number
0 0
Ok
Return
Name
B e d r o m y a n
n
o
Ok
Return
25/11/14
12:48
SOS
Settings
OFF
Enter your code
Info
Settings
My home
OFF
25/11/14
12:48
Testing the installation
5
Test under operating conditions
Test your installation under actual operating conditions by triggering an alarm
with each of your detectors.
During this test, you must take the “exit timer” into account to achieve effective
surveillance (up to 90 seconds).
Test the motion detectors
The motion detector stores each passage in the detection
zone for 90 seconds (whether or not the system is on).
For the test, enable the surveillance from a point where you will not be detected.
Wait for 2 minutes before entering the detection zone
(irrespective of the exit timer).
Whenever the system is activated or deactivated, the alarm control unit sends a
series of beeps indicating that an event (motion detection in this case) has
occurred. You can view this on a touch screen keypad.
To clear the event:
Press and hold the remote control's OFF button for 5 seconds.
The control unit emits beeps when pressed, then a series of beeps after 5 sec-
onds.
Release.
The event is cleared.
The event can also be "cleared" through the Info menu of a CLT 8000 TYXAL+
touch screen keypad.
• If the detector is in delayed triggering mode, the control unit
will only set off the alarm after a programmed time (up to 45
seconds).
During this time, it will emit warning beeps.
• If the alarm control unit does not sound, take another look at
the installation or association of the detector.
• If the installation is equipped with a transmitter, check that the
detection triggers a call cycle to the programmed numbers.
OFF
ON
2'
Activate the
surveillance system
outside of the
detection zone
Enter the detection
zone
Wait for 2 minutes
Stop the
alarm
Beep,
Beep
Alarm control unit
sets off the siren
