manualshive.com logo in svg

DeLonghi WIR1, Руководство пользователя, Страница: 18 / 19

Поделиться
Скачать
DeLonghi WIR1 Скачать руководство пользователя страница 18

18

OBSERVED PROBLEM

POSSIBLE CAUSE

REMEDY

Burner does not light
after ODS/pilot is lit

1. Burner orifice is clogged
2. Inlet gas pressure is too low 

1. Clean burner orifice (see clean-

ing and maintenance, pag 14)
or replace the burner 

2. Contact local natural gas com-

pany

Dalayed ignition of burn-
er 

1. Manifold pressure is too low 
2. Burner orifice is clogged 

1. Contact local natural gas com-

pany

2. Clean burner orifice (see clean-

ing and maintenance, pag 14)
or replace the burner 

Burner backfiring during
combustion

1. Burner orifice is clogged or damaged
2. Burner damaged
3. Gas regulator defective

1. Clean burner orifice (see clean-

ing and maintenance, pag 14)
or replace  the burner

2. Replace burner
3. Replace gas regulator

Burner plaque(s) does not
glow

1. Plaque damaged
2. Control knob set between locked

positions

3. Inlet gas pressure is too low

1. Replace burner
2. Turn control knob until it locks

at desired setting

3. Contact local natural gas com-

pany

Slight smoke or odor dur-
ing initial operation

1. Residues from manufacturing processes  1. Problem will stop after a few

hours of operation

Heater produces whistling
noise when burner is lit

1. turning control knob to HIGH position

when burner is cold

2. Air in gas line
3. Air passageways on heater blocked 
4. Dirty or partially clogged burner ori-

fice 

1. Turn control knob to LOW

position and let warm up for a
minute

2. Operate burner until air is

removed from line. Have gas
line checked by local natural
gas company

3. Observe minimum installation

clearances (see figure 4, page 7

4. Clean burner (see cleaning and

maintenance, page 14) or
replace the burner 

White powder residue
forming with burner box
or on adjacent walls or
furniture

1. When heated, vapors from furniture

polish, wax, carpet cleaners, etc., turn
into white powder residue

1. Turn heater off when using fur-

niture polish, wax, carpet
cleaner or similar products

Note: 

All troubleshooting items

are listed in order of operation

WARNING: 

only a qualified

service person should serv-
ice and repair heater

CAUTION: 

never use

wire,needle, or similar object

to clean  ODS/pilot. This can

damage ODS/pilot unit

WIR 2  26-06-2003  18:21  Pagina 18

Содержание WIR1




















Отзывы:

Нет отзывов