16
SELECTING THE AIR FLOW
In air conditioning and fan modes, press
button (D3) to
select the desired air flow.
The air flows available are:
Minimum air flow:
when most silent operation is
desired.
Maximum air flow
: for maximum performance.
Auto air flow:
the appliance automatically chooses
the air flow based on the temperature selected and
the environmental conditions.
This function is available in the air conditioning mode
and is permanently set in the dehumidifying mode.
SELECT THE TEMPERATURE SCALE
The temperature can be displayed in °C or °F. To change the tem-
perature unit of measure select the air conditioning mode then
press both the decrease
(D5) and increase
(D4) keys for
about 3 sec. The change of the unit of measurement is confirmed
by an acoustic signal.
SETTING THE TIMER
The timer allows the delayed start up or shut down of the appli-
ance. This function will prevent wasting electricity by optimising
the operating periods.
How to program delayed shut down
• While the appliance is on in any operating mode, delayed
shut down can be programmed.
•
Press the
C1
C2
C4
C13
C12
C9
C7
C5
C6
C3
C14
C10
C15
C11
C8
timer button (D6), the timer symbol is dispaly-
ed and the hours
light up.
• Press the (D5) and (D4)
buttons until the desired
numbers of hours to shut down appears on the display.
A few seconds after the timer is set, the setting is acquired, the
display shows the operating mode and the timer symbol stays lit.
Once the set time is elapsed, the air conditioner goes into standby.
To cancel the timer program, press the
C1
C2
C4
C13
C12
C9
C7
C5
C6
C3
C14
C10
C15
C11
C8
timer button (D6)
twice. The timer symbol will go off.
How to program delayed start up
• Plug in the appliance and set to standby.
• Press the
C1
C2
C4
C13
C12
C9
C7
C5
C6
C3
C14
C10
C15
C11
C8
timer button (D6), the timer symbol is dis-
palyed and the hours
light up.
• Press the (D5) and (D4)
buttons until the desired
numbers of hours to start up appears. Start up can be pro-
grammed at any time within the 24 hours that follow.
When the set time is elapsed, the appliance will start to operate
in the same operating mode that was previously set.
To cancel the timer program, press the
C1
C2
C4
C13
C12
C9
C7
C5
C6
C3
C14
C10
C15
C11
C8
timer button (D6)
twice. The timer symbol will go off.
SELF-DIAGNOSIS
The appliance has a self diagnosis system to identify a number of warning/malfunctions.
Error messages are displayed on the appliance display.
IF ... IS DISPLAYED,
“Low Temperature”
(Frost prevention)
..WHAT SHOULD I DO?
The appliance is fitted with a frost protec-
tion device to avoid excessive formation of
ice. The appliance starts up again auto-
matically when the defrosting process is
completed.
IF ... IS DISPLAYED,
“Probe Failure”
(Probe damaged)
..WHAT SHOULD I DO?
If this is displayed, contact your local au-
thorized service center.
IF ... IS DISPLAYED,
“High Level”
(Internal tray full)
..WHAT SHOULD I DO?
Empty the internal safety tank following
the instructions in the section “End of
season operations”.
Содержание PAC ES
