DeLonghi ECAM26455M, Инструкция по эксплуатации

Страница: 20 / 23

19
the appliance has not been used for 3 weeks, you should
replace the filter:
1. Remove the exhausted filter;
2. Remove the new filter from the packaging.
3. Turn the date indicator disk (see fig. 33) until the next 2
months of use are displayed (the filter lasts about two
months);
4. Refill the tank;
5. Insert the filter in the water tank and immerse it
completely, tilting it to enable the air bubbles to escape
(fig. 34);
6. Place the filter in the filter housing (fig. 35aa) and press as
far as it will go. close the tank with the lid (fig. 35b), then
replace the tank in the machine;
7. Position a container with a minimum capacity of 3.4 oz /
100 ml under the hot water spout.
8. Press the menu/esc button to enter the menu;
9. Press the
milK
or
cappuccino
button until “Reset filter
“ is displayed.
10. Press the button;
11. The message “Confirm?” is displayed.
12. Press the
button to confirm the selection;
13. “Hot water, Press OK” is displayed.
14. Press the
button to confirm the selection. the
appliance begins delivering hot water and the message
“Please wait “ is displayed.
15. After delivery, the appliance returns automatically to the
“ready for coffee” position.
The new filter is now active and you can use the coffee maker.
removing the filter
If you want to continue using the appliance without a filter,
you must remove it and notify the appliance of its removal as
follows:
1. Extract the tank and exhausted filter;
2. Press the
menu/esc
button to enter the menu;
3. Press the milK or cappuccino button (fig. 8) until
“Install filter Enabled” is displayed;
4. Press the button
5. “Disable?” is displayed;
6. Press the
button to confirm and the MENU/ESC
button to exit the menu.
technical specification
Voltage: 120V~60 Hz
Absorbed power: 1250W
Pressure: 15 bar
Water tank capacity: 67.62 fl. oz. / 2.0 liters max.
Size Lxhxd: 9.3x13.8x17.5 in / 238x350x445 mm
Cable length: 2,92 ft / 1.80 m
Weight: 260 lb / 11.8 kg
Beans container capacity: 8.82 oz / 250 g max.
Please note
The filter lasts about two months if the appliance is used
normally. If the coffee maker is left unused with the filter
installed, it will last a maximum of three weeks.
3. Remove the tank from the appliance and fill with water.
4. Insert the filter in the water tank and immerse it
completely for ten or so seconds, sloping it to enable the
air bubbles to escape (fig. 34).
5. Insert the filter in the filter housing (fig. 35A) and press as
far as it will go.
6. Close the tank with the lid (fig. 35B), then replace the tank
in the machine.
When you install the filter, you must notify the appliance of its
presence.
7. Press the
menu/esc button to enter the menu;
8. Press the
milK
or
cappuccino button
(fig. 8) until “Install
filter” is displayed;
9. Press the
button;
10. The message “Enable?” is
displayed.
11. Press the
button to confirm the
selection. “Hot water
Confirm?” is displayed.
12. Position a container with
a minimum capacity of
3.4 oz / 100 ml under the
hot water spout.
13. Press the
button to confirm the
selection. The appliance
begins delivering hot
water and the message
“Please wait “ is
displayed.
14. After delivery, the
appliance returns
automatically to the
“Ready
for coffee”
position.
The new filter is active. You can
now use the coffee maker.
replacing the filter
When “REPLACE FILTER” is
displayed, after two months
(see date indicator) or when
33
34
35A
35B