DeLonghi Coffee machine, Инструкция пользователя

Страница: 9 / 34

Note: Use pods which conform to the ESE
standard: this will be indicated on the packaging
by the following symbol:
The ESE standard is a system accepted by the leading
coffee pod manufacturers, and allows espresso coffee
to be prepared simply and without any mess.
• Attach the filter holder onto the machine, moving
from left to right (fig 5).
If the waffle filter holder is used, after using the filter
holder for ground coffee, it is essential to first
remove any coffee grains (fig.24) that may have
stuck to the hot water drip spout. If this cleaning is
not done, water may exit from the sides of the
waffle filter holder while the coffee is being made.
• Proceed as in points 4, 5 and 6 in the previous
section on how to prepare espresso.
• To remove the pod, press the button on the filter
holder and simply lift the pod out
• To turn the coffee machine off, turn the selector knob
on the appliance to the Off position “O” (fig 13).
HOW TO MAKE CAPPUCCINO
1.Prepare espresso coffee, using cups that are large
enough for cappuccinos (see “How to prepare
espresso coffee).
2.Turn the selector knob to the position (fig. 15)
The “cappuccino function” and “boiler on” red lights
will come on. Wait until the orange “OK” light comes
on, to indicate that the boiler has reached the ideal
temperature for producing steam.
3.In the meantime, fill a container with approximately
3 fl. oz of milk for each cappuccino to be prepared.
The milk must be cold from the refrigerator (not
warm!). In choosing the container, bear in mind that
the volume of the milk will increase by 2 or 3 times.
Semi skimmed milk gives best results.
NOTE: We suggest you used semi-skimed milk at
refrigerator temperature.
4.Position the container with the milk in it under the
milk frother (fig. 16).
5.Check that the two holes shown in fig. 19 are not
blocked. If necessary, clean them with the help of a pin
6.Re-attach the steam nozzle by inserting it into the
steam tube and aligning the ‘A’ arrow with the ‘B’
notch, as indicated in figure 20.
7.Re-attach the cappuccino maker by sliding it all the
way into the steam nozzle, aligning the ‘C’ arrow
with the ‘B’ notch, as shown in figure 21, and then
turning it in an anti-clockwise direction.
IMPORTANT: always clean the milk frother and steam
nozzle immediately after use. Proceed as follows:
1.By turning the steam knob (fig. 17), allow a little
steam to come out for a few seconds. Then close
firmly by turning clockwise.
2.Hold the upper part tight with one hand and use your
other hand to unscrew the cappuccino maker,
rotating it in a clockwise direction, and remove it
from the nozzle (fig. 18).
3.Remove the steam nozzle by sliding it off the delivery
tube (fig. 19).
4.Wash the cappuccino maker and steam nozzle
thoroughly with tepid water.
5.Check that the two holes shown in fig. 20 are not
blocked. If necessary, clean them with the help of a pin.
6.Re-attach the steam nozzle by inserting it into the
steam tube and aligning the ‘A’ arrow with the ‘B’
notch, as indicated in figure 20.
7.Re-attach the cappuccino maker by sliding it all the
way into the steam nozzle, aligning the ‘C’ arrow
with the ‘B’ notch, as shown in figure 21, and then
turning it in an anti-clockwise direction.
PRODUCING HOT WATER
1. Turn on the coffee unit by turning the selector knob
to the position (fig. 4).
2. Position a container under the cappuccino maker.
3. When the ‘OK’ pilot light comes on, position the
selector knob at (fig. 7) and at the same time
turn the steam knob in an anti-clockwise direction
(fig. 17); hot water will come out from the
cappuccino maker.
4. To stop the flow of hot water, turn the steam knob in a
clockwise direction and position the selector knob at “O”
CLEANING AND MAINTENANCE
CLEANING THE FILTER HOLDER FOR GROUND COFFEE
After use, it is necessary to clean the filter holder in the
following manner:
• Turn the bottom of the filter holder in an anti-
clockwise direction and take it off (fig. 22).
• Rinse with hot water.
• Replace the bottom.
Every so often it is necessary to eliminate the build up
that forms on the metal crown of the filter holder,
immersing it in hot water for about ten minutes and
then activating the cursor several times.
Never wash the filter holder in the dishwasher.
9
Ofrecido por www.electromanuales.com