Dellmeco DM 15/30 Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 46

background image

36 I DELLMECO I AODD DIAPHRAGM PUMPS

b) Option code SC5, SC6

Differently from the optional equipment codes SC1-SC3, the strokes of the pump are registered pneumatically on

the codes SC5 and SC6. The pressure transmitter registers the changes in pressure within the air chamber behind
one of the diaphragms and it converts the pneumatic impulse into an electrical signal.

The pneumatic stroke counting system is available in two types:

•

SC 5

consist of:

-

pressure transmitter 1-10 bar

-

socket with cable 2,5 m

-

adaptor elbo

w NPT ¼

(or adaptor straight M5 only for DM 15/30 pump)

-

hose DN 4/6; 2,5m

•

SC 6

consist of:

-

SC 5 plus stroke counter

For assembly, screw the adaptor straight into the pressure transmitter (connection P1) and adaptor elbow into

the additional air connection of the pump (it is possible that the adaptors are already installed). The position of the air
inlet varies depending in the pump type and the pump size (see comments below). Link up both adaptors with the
hose.  Connect  the  socket  to  the  electrical  connection  plug  of  the  pressure  transmitter  and  the  cable  to  existing
registering  devices  (Code  SC5)  resp.  to  the  enclosed  stroke  counter  (Code  SC6).  Technical  data,  connection
schemes  and  further  details  can  be  found  in  the  technical  documentation  delivered  by  the  manufacturers  of  the
pressure transmitter and the stroke counter.

The air inlet for the pneumatic stroke counting system must not be confused with the actual air inlet of the pump.

Therefore, you will find some advises adapted to the pump type and the pump size.

Spare part list, stroke counting

Pump size:

DM 15

DM 25

DM 40

DM 50

DM 65

DM 80

Code Pos.

Quantity

Description

Material

Part no.

Part no.

Part no.

Part no.

Part no.

Part no.

SC

1

2

1

Center housing for sensor

PE

-

1 15 09 20

1 25 09 20

1 40 09 20

1 50 09 20 1 80 09 20

1

Center housing for sensor

PE conductive

-

1 15 09 21

1 25 09 21

1 40 09 21

1 50 09 21 1 80 09 21

62

1

Stroke sensor

diverse

-

9 15 16 00

9 15 16 00

9 15 16 00

9 15 16 00 9 15 16 00

SC

2

as SC 1, but additionally contains:

-

1

Clamp amplifier

diverse

-

9 15 18 00

9 15 18 00

9 15 18 00

9 15 18 00 9 15 18 00

-

1

Stroke counter

diverse

-

9 15 17 00

9 15 17 00

9 15 17 00

9 15 17 00 9 15 17 00

SC

3

as SC 1, but additionally contains:

-

1

Level controller

diverse

-

9 15 14 00

9 15 14 00

9 15 14 00

9 15 14 00 9 15 14 00

-

1

Stroke counter

diverse

-

9 15 17 00

9 15 17 00

9 15 17 00

9 15 17 00 9 15 17 00

SC

5

-

1

Center housing with additional

air

connection R ¼”

PE

1 10 109 20 1 15 109 20 1 25 109 20 1 40 109 20 1 50 109 20

-

-

1

PE conductive 1 10 109 21 1 15 109 21 1 25 109 21 1 40 109 21 1 50 109 21

-

-

1

Adaptor elbow

PP

-

1 08 092 28 1 08 092 28 1 08 092 28 1 08 092 28

-

-

1

Adaptor straight

PP

1 08 192 28

-

-

-

-

-

-

1

Hose 2,5 m

PE

1 08 292 28 1 08 292 28 1 08 292 28 1 08 292 28 1 08 292 28

-

-

1

Pressure transmitter

diverse

9 08 28 00

9 08 28 00

9 08 28 00

9 08 28 00

9 08 28 00

-

-

1

Socket with cable 2,5 m

diverse

1 08 392 00 1 08 392 00 1 08 392 00 1 08 392 00 1 08 392 00

-

SC

6

as SC 5, but additionally contains:

-

1

Stroke counter

diverse

9 15 17 00

9 15 17 00

9 15 17 00

9 15 17 00

9 15 17 00

-

!

CAUTION

The pneumatic stroke counting system requires a minimum air pressure of 1.5 bar for optimal function.

«
...
34
35
36
37
38
...
»

Содержание DM 15/30















































Отзывы:

Нет отзывов

Похожие инструкции для DM 15/30

Бренд: Wacker Neuson Страницы: 38

Evosta2 11/139 SAN V

Бренд: DAB Страницы: 31

Бренд: DAB Страницы: 19

Бренд: P.Lindberg Страницы: 54

Бренд: PerformancePro Страницы: 15

Бренд: IWAKI PUMPS Страницы: 64

Бренд: Rheem Страницы: 1

Fybroc series 1530

Бренд: Met-Pro Страницы: 22

Бренд: Nortek Страницы: 52

jumbo floodfighter

Бренд: Davey Страницы: 8

Бренд: F.F. Group Страницы: 28

Бренд: ICP Страницы: 14

WS G140DC6 Series

Бренд: Waterstage Страницы: 64

Бренд: IBC Страницы: 8

Бренд: Raypak Страницы: 40

Бренд: red lion Страницы: 8

FLOWMAX PU 2125 F

Бренд: SAMES KREMLIN Страницы: 32

Бренд: ubbink Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды