background image

Curved edge

DDR4 modules feature a curved edge to help with insertion and alleviate stress on the PCB during memory installation.

Figure 3. Curved edge

Memory Errors

Memory errors on the system display the new ON-FLASH-FLASH or ON-FLASH-ON failure code. If all memory fails, the LCD does not 
turn on. Troubleshoot for possible memory failure by trying known good memory modules in the memory connectors on the bottom of the 
system or under the keyboard, as in some portable systems.

NOTE: 

The DDR4 memory is imbedded in board and not a replaceable DIMM as shown and referred.

HDMI 1.4

This topic explains the HDMI 1.4 and its features along with the advantages.

HDMI (High-Definition Multimedia Interface) is an industry-supported, uncompressed, all-digital audio/video interface. HDMI provides an 
interface between any compatible digital audio/video source, such as a DVD player, or A/V receiver and a compatible digital audio and/or 
video monitor, such as a digital TV (DTV). The intended applications for HDMI TVs, and DVD players. The primary advantage is cable 
reduction and content protection provisions. HDMI supports standard, enhanced, or high-definition video, plus multichannel digital audio 
on a single cable.

NOTE: 

The HDMI 1.4 will provide 5.1 channel audio support.

HDMI 1.4 Features

HDMI Ethernet Channel 

- Adds high-speed networking to an HDMI link, allowing users to take full advantage of their IP-enabled 

devices without a separate Ethernet cable

Audio Return Channel

 - Allows an HDMI-connected TV with a built-in tuner to send audio data "upstream" to a surround audio 

system, eliminating the need for a separate audio cable

3D

 - Defines input/output protocols for major 3D video formats, paving the way for true 3D gaming and 3D home theater applications

Content Type

 - Real-time signaling of content types between display and source devices, enabling a TV to optimize picture settings 

based on content type

Additional Color Spaces 

- Adds support for additional color models used in digital photography and computer graphics

4K Support

 - Enables video resolutions far beyond 1080p, supporting next-generation displays that will rival the Digital Cinema 

systems used in many commercial movie theaters

HDMI Micro Connector

 - A new, smaller connector for phones and other portable devices, supporting video resolutions up to 1080p

Automotive Connection System

 - New cables and connectors for automotive video systems, designed to meet the unique 

demands of the motoring environment while delivering true HD quality

Advantages of HDMI

Quality HDMI transfers uncompressed digital audio and video for the highest, crispest image quality.

Low -cost HDMI provides the quality and functionality of a digital interface while also supporting uncompressed video formats in a 
simple, cost-effective manner

Audio HDMI supports multiple audio formats from standard stereo to multichannel surround sound

HDMI combines video and multichannel audio into a single cable, eliminating the cost, complexity, and confusion of multiple cables 
currently used in A/V systems

Technology and components

9

Содержание Vostro 3583






















































































Отзывы: