background image

  

6

. Trouble Shooting Instructions

Self-Test

Your monitor provides a self-test feature that allows you to check whether your 
monitor is functioning properly. If your monitor and computer are properly connected 
but the monitor screen remains dark, run the monitor self-test by performing the 
following steps:

1. 

Turn off both your computer and the monitor.

2. 

Unplug the video cable from the back of the computer. To ensure proper Self-Test 
operation, remove all digital and the analog cables from the back of computer.

3. 

Turn on the monitor.

The floating dialog box should appear on-screen (against a black background), if the 
monitor cannot sense a video signal and is working correctly. While in self-test mode, 
the power LED remains white. Also, depending upon the selected input, one of the 
dialogs shown below will continuously scroll through the screen.

No DP Cable

The display will go into Standby Mode in 4 minutes.

www.dell.com/U

30

23

E

/U2723QE/U3223QE

or

No HDMI Cable

The display will go into Standby Mode in 4 minutes.

www.dell.com/U

30

23

E

/U2723QE/U3223QE

or

No USB-C Cable

The display will go into Standby Mode in 4 minutes.

www.dell.com/U

30

23

E

/U2723QE/U3223QE

4. 

This box also appears during normal system operation if the video cable becomes 
disconnected or damaged.

5. 

Turn off your monitor and reconnect the video cable; then turn on both your 
computer and the monitor.

If your monitor screen remains blank after you use the previous procedure, check your 
video controller and computer, because your monitor is functioning properly.

Содержание U2723QE



























Отзывы: