manualshive.com logo in svg

Dell S5448F-ON, Руководство по установке

Поделиться
Скачать
Dell S5448F-ON Скачать руководство пользователя страница 41

Installing ONIE on: /dev/sda

ONIE: Success: Firmware update URL: file:///lib/onie/onie-updater.tar

ONIE: Success: Firmware update version: x.xx.x.x-x

ONIE: Rebooting...

discover: ONIE embed mode detected.

Stopping: discover...start-stop-daemon: warning: killing process 897: No such process

 done. 

Topics:

•

Enable BIOS secure boot

•

Disable BIOS secure boot

Enable BIOS secure boot

The Secure Boot configuration page in the BIOS Setup menu is password protected. If Secure Boot mode is not enabled on your
switch, use the following process to enable Secure Boot mode.

1. Enter the BIOS password. The default password is the switch service tag plus an exclamation mark; for example, 

xxxxxx!

.

After first login, to change the default password, select the 

Security

 tab then select 

Administrator Password

. Enter and

confirm the new Administrator password. The Administrator password range is 3 to 20 characters.
After you enter the Administrator password, you enter the Main tab of the BIOS user interface.

2. Select the 

Security

 tab using the right arrow key.

Secure boot

41

Содержание S5448F-ON

























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды