•
metric-value
: the range is from 0 to 16777215. The default is
0
.
•
metric-type
: choose either external or internal. The default is
internal
.
•
map-name
: enter the name of a configured route map.
• Include specific OSPF routes in IS-IS.ROUTER ISIS mode
redistribute ospf
process-id
[level-1| level-1-2 | level-2] [metric
value
]
[match external {1 | 2} | match internal] [metric-type {external | internal}]
[route-map
map-name
]
Configure the following parameters:
•
process-id
: the range is from 1 to 65535.
•
level-1
,
level-1-2
, or
level-2
: assign all redistributed routes to a level. The default is
level-2
.
•
metric
value
: the range is from 0 to 16777215. The default is
0
.
•
metric
value
: the range is from 0 to 16777215. The default is
0
.
•
match external
: the range is 1 or 2.
•
match internal
•
metric-type
: external or internal.
•
map-name
: name of a configured route map.
To view the IS-IS configuration globally (including both IPv4 and IPv6 settings), use the
show running-
config isis
command in EXEC Privilege mode. To view the current IPv4 IS-IS configuration, use the
show
config
command in ROUTER ISIS mode. To view the current IPv6 IS-IS configuration, use the
show config
command in ROUTER ISIS-ADDRESS FAMILY IPV6 mode.
Configuring Authentication Passwords
You can assign an authentication password for routers in Level 1 and for routers in Level 2.
Because Level 1 and Level 2 routers do not communicate with each other, you can assign different passwords
for Level 1 routers and for Level 2 routers. However, if you want the routers in the level to communicate with
each other, configure them with the same password.
To configure a simple text password, use the following commands.
• Configure authentication password for an area.
ROUTER ISIS mode
area-password [hmac-md5]
password
The Dell OS supports HMAC-MD5 authentication.
This password is inserted in Level 1 LSPs, Complete SNPs, and Partial SNPs.
• Set the authentication password for a routing domain.
ROUTER ISIS mode
domain-password [
encryption-type
| hmac-md5]
password
The Dell OS supports both DES and HMAC-MD5 authentication methods.
This password is inserted in Level 2 LSPs, Complete SNPs, and Partial SNPs.
Intermediate System to Intermediate System
572
Содержание S4048T
