Dell Precision M20 страница 39 Скачать руководство пользователя

Страница: 39 / 47

Back to Contents Page

Microprocessor Thermal-Cooling Assembly

Dell Precision™ M20 Service Manual

Removing the Microprocessor Thermal-Cooling Assembly

Installing the Microprocessor Thermal-Cooling Assembly

Removing the Microprocessor Thermal-Cooling Assembly

Follow the instructions in "

Preparing to Work Inside the Computer

Remove the

center control cover

Remove the

keyboard

Remove the

display assembly

Remove the

palm rest

Loosen in consecutive order the three captive screws, labeled "1" through "3," that secure the microprocessor thermal-cooling assembly to the system
board.

Lift to remove the microprocessor thermal-cooling assembly away from the system board.

Installing the Microprocessor Thermal-Cooling Assembly

Place the microprocessor thermal-cooling assembly on the system board.

Tighten the three captive screws, labeled "1" through "3," in consecutive order.

CAUTION:

Before you begin any of the procedures in this section, follow the safety instructions located in the

Product Information Guide

NOTICE:

To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such

as the back panel) on the computer.

NOTICE:

Disconnect the computer and any attached devices from electrical outlets, and remove any installed batteries.

NOTE:

You can remove the microprocessor thermal-cooling assembly with the fan attached.

microprocessor thermal-cooling assembly

captive screws (3)

Содержание Precision M20
















































Результаты поиска

Содержание Precision M20

Отзывы:

Похожие инструкции для Precision M20

Бренды по названию

Популярные бренды

Dell Precision M20, Руководство по обслуживанию

Результаты поиска

Содержание Precision M20

Отзывы:

Похожие инструкции для Precision M20

Бренды по названию

Популярные бренды