Dell PowerEdge M600 Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 236

background image

30

About Your System

iKVM Module

The optional Avocent iKVM analogue switch module includes the following
features:

•

Local iKVM access can be remotely disabled on a per blade basis, using the
blade’s iDRAC interface (access is enabled by default).

NOTE:

By default (enabled), a console session to a given blade will be

available to both the iDRAC interface and iKVM (users connected to a blade's
console via iDRAC and the iKVM will see the same video and be able to type
commands). If this sharing is not desired, this can be disabled via the iDRAC
console interface.

•

The following connectors:

–

One VGA connector. The iKVM supports a video display resolution
range from 640x480 at 60Hz up to 1280x1024x65,000 colors
(noninterlaced) at 75Hz.

–

Two USB ports for keyboard and mouse.

NOTE:

The iKVM USB ports do not support storage devices.

Table 1-6.

Fan Indicators

Indicator

Indicator
State

Description

Power indicator Green

The power supply is connected to an 208VAC
AC power source.

NOTE:

This indicator will not illuminate if the

power supply is connected to a 110 VAC power
source.

Off

AC power not connected.

Fault indicator

Amber

The fan is in a fault condition.

Off

Fan not faulty.

«
...
28
29
30
31
32
...
»

Содержание PowerEdge M600













































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PowerEdge M600

Бренд: FabiaTech Страницы: 4

Бренд: Patton electronics Страницы: 16

HAWA-Frontside 60/B

Бренд: hawa Страницы: 28

Бренд: Telit Wireless Solutions Страницы: 113

Бренд: peplink Страницы: 2

Бренд: Accom Страницы: 15

Бренд: Barco Страницы: 30

AXP-100H MUSCLE

Бренд: Thermalright Страницы: 36

Бренд: Z3 Technology Страницы: 67

DL-DVI-Vision-IP Series

Бренд: G&D Страницы: 228

CY62136EV30 MoBL

Бренд: Cypress Semiconductor Страницы: 12

Бренд: Abit Страницы: 22

Suzie-Q 541.35.520

Бренд: Hafele Страницы: 12

Бренд: IEI Technology Страницы: 4

Бренд: SilverStone Страницы: 28

DAS-1800HR Series

Бренд: Keithley Страницы: 139

PSJ-VZ58 gen3 OEM

Бренд: Grizzly Страницы: 12

i.MX 8M Mini LPDDR4 EVK

Бренд: NXP Semiconductors Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды