Dell PowerEdge M600 Скачать руководство пользователя страница 171

Страница: 171 / 236

Installing Enclosure Components

171

Figure 4-8.

Removing and Installing the Front Module Cage Assembly

NOTICE:

The empty cage assembly weighs 21 kg (47 pounds). Obtain assistance

when removing the cage assembly from the enclosure.

Slide the cage out from the enclosure. See Figure 4-8.

Disconnect the control-panel cable from the midplane by pressing the
small latch at each end of the connector.

Remove the four T-15 Torx screws securing the midplane to the back of
the front cage assembly, and remove the midplane. See Figure 4-9.

front module cage assembly

enclosure

screws (4)

Содержание PowerEdge M600













































































































































































































































Результаты поиска

Содержание PowerEdge M600

Отзывы:

Похожие инструкции для PowerEdge M600

Бренды по названию

Популярные бренды

Dell PowerEdge M600, Руководство владельца оборудования

Результаты поиска

Содержание PowerEdge M600

Отзывы:

Похожие инструкции для PowerEdge M600

Бренды по названию

Популярные бренды