Dell PowerEdge M600 Скачать руководство пользователя страница 169

Страница: 169 / 236

Installing Enclosure Components

169

Figure 4-7.

Removing and Installing the Bezel

Installing the Enclosure Bezel

Attach the bezel to the enclosure using the eight screws. See Figure 4-7.

Connect the ribbon cable to the LCD module, and reinstall the cover
plate.

Enclosure Midplane (Service Only)

Removing the Front Module Cage Assembly and Midplane

CAUTION:

Only trained service technicians are authorized to remove the system

cover and access any of the components inside the system. Before you begin this
procedure, review the safety instructions that came with the system.

bezel

enclosure

screws (8)

Содержание PowerEdge M600













































































































































































































































Результаты поиска

Содержание PowerEdge M600

Отзывы:

Похожие инструкции для PowerEdge M600

Бренды по названию

Популярные бренды

Dell PowerEdge M600, Руководство владельца оборудования

Результаты поиска

Содержание PowerEdge M600

Отзывы:

Похожие инструкции для PowerEdge M600

Бренды по названию

Популярные бренды