Dell PowerEdge M600 Скачать руководство пользователя страница 164 | Manualshive

Страница: 164 / 236

background image

164

Installing Enclosure Components

Installing an SD Card in the CMC Module

The SD card slot on the CMCM module supports an optional WWN/MAC
feature that allows slot-based WWN/MACs for the blades, simplifying blade
installation and replacement.

NOTE:

For a redundant CMC module system, install the SD card on the passive

module. The blue status indicator will be off on the passive module.

1

Remove the CMC module from the M1000e enclosure. See "Removing a
CMC Module" on page 162.

NOTE:

Verify the write protection latch is in the "unlock" position.

2

Locate the SD card slot on the bottom of the CMC module and insert the
contact-pin end of the card into the slot with the label on the card facing
upwards. See Figure 4-5.

Figure 4-5.

Installing an SD Card in the CMC Module

1

SD card

2

SD card connector

2

1

«
...
162
163
164
165
166
...
»

Содержание PowerEdge M600













































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PowerEdge M600

Express EtherNetwork DFE-670TXD

Бренд: D-Link Страницы: 4

Бренд: DAD Страницы: 36

Бренд: D-Link Страницы: 2

Бренд: Idis Страницы: 31

iW-RainboW-G30D

Бренд: iWave Страницы: 89

MegaRAID SATA 300-4XLP

Бренд: LSI Страницы: 3

BIC 1I12-P2A25-M30MI1-BPX05-110

Бренд: Balluff Страницы: 12

USB-BRIDGEV2-EVAL

Бренд: IDT Страницы: 11

Бренд: XtendLan Страницы: 228

Through Hole Power Inductors 1411

Бренд: Delta Electronics Страницы: 1

Бренд: Caen Страницы: 14

Бренд: CNC4PC Страницы: 11

Бренд: Xtreme Страницы: 83

Бренд: ATTO Technology Страницы: 2

Бренд: AMC Страницы: 28

Бренд: Cypress Semiconductor Страницы: 38

Бренд: Hologic Страницы: 256

Бренд: ANTAIRA Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды