Dell PowerEdge 700 Скачать руководство пользователя страница 76

Страница: 76 / 94

Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet.

Remove the bezel. See "

Removing the Bezel

" in "Troubleshooting Your System."

Lay the system on its right side.

Remove the cover. See "

Removing the Cover

" in "Troubleshooting Your System."

Remove the cooling shroud. See "

Removing the Cooling Shroud

" in "Installing System Options."

Disconnect the interface and power cables to the hard drives in the drive bay.

Remove the hard-drive bay. See

Loosen the four screws that secure the drive bay to the system.

Slide the hard-drive bay out of the system.

Remove the drive from the drive bay. See

Remove the screws that secure the drive in the hard-drive bay.

Slide the drive out of the drive bay.

Figure 7-5. Removing a SATA Hard Drive

Figure 7-6. Removing a Cabled SCSI Hard Drive

CAUTION:

See your

System Information Guide

for complete information about safety precautions working inside the computer and protecting

against electrostatic discharge.

Содержание PowerEdge 700































































































Результаты поиска

Содержание PowerEdge 700

Отзывы:

Похожие инструкции для PowerEdge 700

Бренды по названию

Популярные бренды

Dell PowerEdge 700, Инструкция по установке и устранению неисправностей

Результаты поиска

Содержание PowerEdge 700

Отзывы:

Похожие инструкции для PowerEdge 700

Бренды по названию

Популярные бренды