Dell PowerConnect W-6000 Скачать руководство пользователя страница 3

Dell PowerConnect W-6000 Power Supply

| Installation Guide

3

Power Switch: The power switch has two states: Off (

) and On (|).

Power Management

The W-6000 supports up to three 400 W power supplies. If using one to two primary power supplies for 400 to 
800 W of primary power, the use of a 400 W redundant power supply is possible.

For maximum capacity planning, add the maximum power draw required for all of the modules in your chassis 
configuration to determine the required number of power supplies. 

M3 Module and PSU Configuration Table

The following table displays the M3 module configurations, and the resultant power supply configurations and 
power usage.

Table 2  

Power Supply and W-6000M3 Configurations

Inserting a Power Supply

1. Verify you understand the procedure and all precautions.

Before beginning, read the entire procedure. Verify you understand all the precautions in these steps as well as 
those on page 10.

2. Select a power supply slot for the power supply.

The 400 W power supply (HW-PSU-400) can be installed in any power supply slot and any power supply 
slot can be left empty. That is, there is no specific required order of slots used for power supplies.

Figure 2  

400 W Power Supplies Installed

If replacing a previously installed power supply, first see 

“Removing a Power Supply” on page

 

5

.

If you are installing a power supply in an empty slot, you may have to remove the blank cover plate first. To do 
this, use a #2 Phillips or cross-head screwdriver. Turn the captive fastening screws on the faceplate counter-
clockwise until they are loose (they cannot be completely removed). Remove the cover plate and store it in a safe 
place.

Module

Number of Units

M3 Controller Module

(130 W max power draw each)

1

2

3

4

Total Power (W)

130

260

390

520

Required number of PSUs

1

1

1

2

Redundant number of PSUs

1 or 2 1 or 2 1 or 2 1

7

CAUTION:  Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple 
repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. 
Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions 
that came with the product.

Содержание PowerConnect W-6000







Отзывы: