Dell PowerConnect J-8216 Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 270

Dell PowerConnect J-8216 Скачать руководство пользователя страница 30

Slot Numbering for a J-EX8216 Switch

A J-EX8216 chassis accepts 16 line cards, two Routing Engine (RE) modules, eight Switch
Fabric (SF) modules, two fan trays, and six AC power supplies. All 16 slots for the line
cards and the two slots for the RE modules run horizontally across the front of the chassis.
The fan tray slots run vertically on the left of the chassis front. The six power supply slots
run vertically across the front bottom of the chassis. The eight slots for the SF modules
run vertically on the chassis rear.

•

Slot Numbering for RE Module Slots and Line Card Slots on page 14

•

Slot Numbering for the Power Supply Slots on page 16

•

Slot Numbering for the SF Module Slots on page 17

Slot Numbering for RE Module Slots and Line Card Slots

The slot labels for the RE module slots and the line card slots appear in two columns on
each fan tray. The labels are identical on both fan trays, allowing you to use either fan
tray in either fan tray slot. You read the slot labels based on the location of the fan trays.
On the top fan tray, read the inner column of labels. On the bottom fan tray, read the
outer column of labels. Table 8 on page 14 lists the slot numbers on the J-EX8216 fan
trays and the components those slots accept.

Table 8: Slot Numbering on the J-EX8216 Fan Trays

Components Accepted in Slot

Inner Slot Label (Read
for Top Fan Tray)

Outer Slot Label
(Read for Bottom Fan
Tray)

•

RE module (adjacent to top fan tray)

•

Line card (adjacent to bottom fan tray)

RE0

7

•

RE module (adjacent to top fan tray)

•

Line card (adjacent to bottom fan tray)

RE1

8

Line card

0

9

Line card

1

10

Line card

2

11

Line card

3

12

Line card

4

13

Line card

5

14

Line card

6

15

Figure 5 on page 15 shows the slot numbering on the fan trays:

14

Dell PowerConnect J-Series J-EX8216 Ethernet Switch Hardware Guide

«
...
28
29
30
31
32
...
»

Содержание PowerConnect J-8216















































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды