Dell PowerConnect J-8216 Скачать руководство пользователя страница 187

Страница: 187 / 270

To disconnect a fiber-optic cable from an optical transceiver installed in the switch:

Disable the port in which the transceiver is installed by issuing the command:

[edit interfaces]

user@switch#

set

interface-name

disable

WARNING:

Do not look directly into a fiber-optic transceiver or into the

ends of fiber-optic cables. Fiber-optic transceivers and fiber-optic cables
connected to transceivers emit laser light that can damage your eyes.

Carefully unplug the fiber-optic cable connector from the transceiver.

Cover the transceiver with a rubber safety cap.

WARNING:

Do not leave a fiber-optic transceiver uncovered except when

inserting or removing a cable. The rubber safety cap keeps the port clean
and prevents accidental exposure to laser light.

Cover the fiber-optic cable connector with the rubber safety cap.

Documentation

Connecting a Fiber-Optic Cable to a J-EX Series Switch on page 127

•

Removing a Transceiver from a J-EX Series Switch on page 168

•

Maintaining Fiber-Optic Cables in J-EX Series Switches on page 179

•

Optical Interface Support in J-EX8200 Switches on page 51

Removing the Power Cord Tray from a Rack or Cabinet for a J-EX8200 Switch

You can remove the power cord tray from a rack or cabinet. (The remainder of this topic
uses “rack” to mean “rack or cabinet.”)

NOTE:

The J-EX8216 switch can be installed only in a four-post rack.

Installation in a two-post rack is not supported.

Before you begin to remove the power cord tray:

•

Ensure no power cables are resting on or threaded through the power cord tray.

Ensure that you have the following parts and tools available to remove the power cord
tray:

•

A Phillips (+) screwdriver, number 1, 2, or 3, depending on the size of your rack mounting
screws

171

Chapter 13: Removing Switch Components

Содержание PowerConnect J-8216















































































































































































































































































Результаты поиска

Содержание PowerConnect J-8216

Отзывы:

Бренды по названию

Популярные бренды

Dell PowerConnect J-8216, Руководство по оборудованию

Результаты поиска

Содержание PowerConnect J-8216

Отзывы:

Бренды по названию

Популярные бренды