manualshive.com logo in svg

Dell PowerConnect J-8216, Руководство по оборудованию

Поделиться
Скачать
Dell PowerConnect J-8216 Скачать руководство пользователя страница 184

CAUTION:

Do not stack line cards on top of one another or on top of any

other component. Place each line card separately in the antistatic bag or
on the antistatic mat placed on a flat, stable surface.

CAUTION:

The line cards in J-EX8200 switches weigh more than 10 lb

(4.5 kg). Be prepared to accept the full weight as you slide the line card
out of the chassis.

8.

Place one hand around the faceplate of the line card and the other hand under the
line card to support it. Taking care not to touch line card components, pins, leads, or
solder connections, gently slide the line card completely out of the chassis and place
it in an antistatic bag or on its own antistatic mat placed on a flat, stable surface.

CAUTION:

After removing a line card, wait for at least 30 seconds before

installing a line card or removing another line card.

9.

If you are not installing a line card in the emptied line card slot within a short time,
install a blank cover panel over the slot and secure it with captive screws by using the
screwdriver. Do this to protect the interior of the chassis from dust or other foreign
substances and to ensure that the airflow inside the chassis is not disrupted.

Figure 76: Removing a Line Card from a J-EX8200 Switch Chassis

Related

Documentation

Installing a Line Card in a J-EX8200 Switch on page 123

•

•

8-port SFP+ Line Card in a J-EX8200 Switch on page 32

•

48-port SFP Line Card in a J-EX8200 Switch on page 33

•

48-port RJ-45 Line Card in a J-EX8200 Switch on page 34

Removing a Transceiver from a J-EX Series Switch

The transceivers for J-EX Series switches are hot-removable and hot-insertable
field-replaceable units (FRUs): You can remove and replace them without powering off
the switch or disrupting switch functions.

168

Dell PowerConnect J-Series J-EX8216 Ethernet Switch Hardware Guide

Содержание PowerConnect J-8216















































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды