background image

2. Gently press down on the display hinges to align the screw holes on the display hinges with the screw holes on the palm-rest

and keyboard assembly.

3. Replace the four (M2.5x5) screws that secure the display hinges to the palm-rest and keyboard assembly.

NOTE:

 The power-adapter port is secured in place by the left display hinge. There is no screw, tape, or adhesives

securing the power-adapter port to the palm rest. As a result technicians should take note of whether or not the power
adapter port has fallen out of the system during subsequent removal procedures.

4. Connect the display cable to the connector on the system board.

Next steps

1. Install the 

base cover

.

2. Install the 

SD card

.

3. Follow the procedure in 

After working inside your computer

.

Removing the display assembly (Plastic)

Prerequisites

1. Follow the procedure in 

Before working inside your computer

.

2. Remove the 

SD card

.

3. Remove the 

base cover

.

4. Remove the 

SSD

.

5. Remove the 

wireless card

.

About this task

The following images indicate the location of the display assembly and provide a visual representation of the removal procedure.

Removing and installing components

49

Содержание P152G







































































































Отзывы: