Dell P152G Скачать руководство пользователя страница 44

Страница: 44 / 102

Steps

1. Using the alignment posts, place the power button with fingerprint reader into its slot on the palmrest and keyboard

assembly.

2. Replace the (M2x2) screw that secures the power button with fingerprint reader to the palmrest and keyboard assembly.
3. Adhere the fingerprint reader Flexible Flat cable to the palmrest and keyboard assembly

NOTE:

Fold and align the fingerprint reader Flexible Flat cable to the mark at the right of the power button, and align

the white line on the Flexible Flat cable to the mark on the palmrest and keyboard assembly.

4. Close the display hinge.
5. Replace the two (M2.5x5) screws that secure the display hinge to the palmrest and keyboard assembly.

Next steps

1. Install the

2. Install the

3. Install the

4. Install the

5. Install the

6. Follow the procedure in

After working inside your computer

Display assembly

Removing the display assembly (Aluminum)

Prerequisites

1. Follow the procedure in

Before working inside your computer

2. Remove the

SD card

3. Remove the

base cover

About this task

The following images indicate the location of the display assembly and provide a visual representation of the removal procedure.

Removing and installing components

Содержание P152G







































































































Результаты поиска

Содержание P152G

Отзывы:

Похожие инструкции для P152G

Бренды по названию

Популярные бренды

Dell P152G, Руководство по обслуживанию

Результаты поиска

Содержание P152G

Отзывы:

Похожие инструкции для P152G

Бренды по названию

Популярные бренды