Dell Networking S6000 System Скачать руководство пользователя

Страница: 901 / 1510

Version 7.4.1.0

Introduced on the E-Series.

debug lldp interface

To display timer events, neighbor additions or deletions, and other information about incoming and
outgoing packets, enable LLDP debugging.

S6000

Syntax

debug lldp interface {

interface

| all}{events | packet {brief |

detail} {tx | rx | both}}

To disable debugging, use the

no debug lldp interface {

interface

all}{events} {packet {brief | detail} {tx | rx | both}}

command.

Parameters

interface

Enter the following keywords and slot/port or number
information:
• For a Fast Ethernet interface, enter the keyword

FastEthernet

then the slot/ port information.

• For a 1-Gigabit Ethernet interface, enter the keyword

GigabitEthernet

followed by the slot/ port

information.

• For a 10-Gigabit Ethernet interface, enter the keyword

tenGigabitEthernet

then the slot/port information.

• For a 40-Gigabit Ethernet interface, enter the keyword

fortyGigE

then the slot/port information.

NOTE: The

FastEthernet

option is not supported on

the S-Series.

all

(OPTIONAL) Enter the keyword

all

to display information

on all interfaces.

events

(OPTIONAL) Enter the keyword

events

to display major

events such as timer events.

packet

(OPTIONAL) Enter the keyword

packet

to display

information regarding packets coming in or going out.

brief

(OPTIONAL) Enter the keyword

brief

to display brief packet

information.

detail

(OPTIONAL) Enter the keyword

detail

to display detailed

packet information.

(OPTIONAL) Enter the keyword

to display transmit-only

packet information.

(OPTIONAL) Enter the keyword

to display receive-only

packet information.

both

(OPTIONAL) Enter the keyword

both

to display both receive

and transmit packet information.

Link Layer Discovery Protocol (LLDP)

901

Содержание Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание Networking S6000 System

Отзывы:

Похожие инструкции для Networking S6000 System

Бренды по названию

Популярные бренды

Dell Networking S6000 System, Справочное руководство

Результаты поиска

Содержание Networking S6000 System

Отзывы:

Похожие инструкции для Networking S6000 System

Бренды по названию

Популярные бренды