Dell Networking S6000 System Скачать руководство пользователя | Manualshive

Страница: 1454 / 1510

background image

55

VLT Proxy Gateway

This chapter describes the VLT Proxy Gateway feature.

proxy-gateway lldp

Configure the LLDP proxy gateway

S6000

Syntax

proxy-gateway lldp

Command
Modes

VLT DOMAIN

Command
History

Version 9.4(0.0)

Introduced on the S4810, S4820T, S6000, Z9000, and MXL
Switch.

Usage
Information

The configuration is cached and sent to LLDP only in one of the following
conditions:
1) The port-channel connecting the two VLT domains, across DC, must be a VLT
LAG

2) The protocol lldp command is globally enabled

3) The proxy-gateway LLDP configuration is applied.

However, “proxy-gateway lldp” configuration is sent to the Layer 2 application.
When LLDP sends an IPC reply message, SWPQ is created towards LLDP to send
further updates to LLDP. When the proxy gateway peer-domain-link port-channel
command is provisioned, the configuration is sent to LLDP if the port-channel is a
VLT port-channel. However it will not check whether the port-channel is up or
down. LLDP determines the addition and removal of LAG ports and transmits LLDP
packets out accordingly.

Example

Dell(conf)#vlt-domain 1

Dell(conf-vlt-domain#proxy-gateway lldp

1454

VLT Proxy Gateway

«
...
1452
1453
1454
1455
1456
...
»

Содержание Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Networking S6000 System

Бренд: ABLE Страницы: 5

Бренд: Datavideo Страницы: 2

COOPER POWER SERIES

Бренд: Eaton Страницы: 16

Бренд: PureLink Страницы: 10

Бренд: FS Страницы: 41

Бренд: HIKVISION Страницы: 5

Бренд: Endress+Hauser Страницы: 25

DigiTOOLS VS-41USB

Бренд: Kramer Страницы: 8

TK-205K - PS/2 KVM Switch

Бренд: TRENDnet Страницы: 11

Бренд: Raritan Страницы: 4

Бренд: Atlona Страницы: 13

Valena Life LE-752107

Бренд: LEGRAND Страницы: 5

Бренд: Led Control Страницы: 22

Бренд: SMART-AVI Страницы: 8

Бренд: H3C Страницы: 31

Бренд: Arista Страницы: 46

Бренд: Rose electronics Страницы: 52

Бренд: Rose electronics Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды