Dell Networking S6000 System Скачать руководство пользователя | Manualshive

Страница: 1106 / 1510

background image

40

Quality of Service (QoS)

The Dell Networking operating software commands for quality of service (QoS) include traffic

conditioning and congestion control. QoS commands are not universally supported on all Dell
Networking Products.S6000 platform.
This chapter contains the following sections:

•

Global Configuration Commands

•

Per-Port QoS Commands

•

Policy-Based QoS Commands

Global Configuration Commands

There is only one global configuration QoS command.

qos-rate-adjust

By default, while rate limiting, policing, and shaping, Dell Networking OS does not include the Preamble,

SFD, or the IFG fields. These fields are overhead; only the fields from MAC destination address to the CRC

are used for forwarding and are included in these rate metering calculations. You can optionally include

overhead fields in rate metering calculations by enabling QoS Rate Adjustment.

S6000

Syntax

qos-rate-adjustment

overhead-bytes

Parameters

overhead-bytes

Include a specified number of bytes of packet overhead to
include in rate limiting, policing, and shaping calculations.
The range is from 1 to 31.

Defaults

QoS rate adjustment is disabled by default.

Command
Modes

CONFIGURATION

Command
History

This guide is platform-specific. For command information about other platforms,
refer to the relevant

Dell Networking OS Command Line Reference Guide

.

The following is a list of the Dell Networking OS version history for this command.

Version 9.0.2.0

Introduced on the S6000.

Version
8.3.19.0

Introduced on the S4820T.

1106

Quality of Service (QoS)

«
...
1104
1105
1106
1107
1108
...
»

Содержание Networking S6000 System







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Networking S6000 System

COOPER POWER SERIES

Бренд: Eaton Страницы: 24

COOPER POWER SERIES

Бренд: Eaton Страницы: 16

Crouse-hinds series

Бренд: Eaton Страницы: 16

Cutler-Hammer AMPGARD

Бренд: Eaton Страницы: 4

Бренд: Raritan Страницы: 4

Бренд: rako Страницы: 4

Бренд: DAITEM Страницы: 37

AVS-OP-1616-340

Бренд: AMX Страницы: 1

Бренд: INFLUX MEASUREMENTS Страницы: 6

Бренд: Intermatic Страницы: 1

SecureStack C3K-2XFP IOM

Бренд: Enterasys Страницы: 72

SANbox 5000 Series

Бренд: Qlogic Страницы: 2

Бренд: Clas Ohlson Страницы: 4

Бренд: ddtop Страницы: 10

Бренд: ELPRO Страницы: 8

kontron KSwitch D4 MF

Бренд: S&T Страницы: 100

Бренд: Quintech Страницы: 2

Бренд: N-Tron Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды