background image

Back to Contents Page

  

 

 Communications Cards  

Dell™ Latitude™ D631 Service Manual

 

  

Wireless Local Area Network (WLAN) Card 

 

  

Mobile Broadband Network (WWAN) Card 

 

  

Subscriber Identity Module (SIM) Card 

 

 

 

Wireless Local Area Network (WLAN) Card  

 

 

 

 

If you ordered a WLAN card with your computer, the card is already installed. 

 

 

1.

Follow the procedures in 

Before You Begin

.  

 

 

  

2.

Remove the hinge cover (see 

Hinge Cover

).  

 

 

  

3.

Remove the keyboard (see 

Removing the Keyboard

).  

 

  

 

 

4.

If a WLAN card is not already installed, go to 

step 5

. If you are replacing a WLAN card, remove the existing card:  

 

a.

 

Disconnect the antenna cables from the card.  

 

b.

 

Release the card by pushing the metal securing tabs away from the card until the card pops up slightly.  

 

c.

 

Slide the card at a 45-degree angle out of its connector.  

 

 

CAUTION: 

Before you begin any of the procedures in this section, follow the safety instructions in the 

Product Information Guide

.

 

CAUTION: 

To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal 

surface, such as a connector on the back of the computer.

WLAN card 

antenna cables (2) 

 

 

 

 

 

NOTICE: 

To prevent damage to the connector, do not use tools to release the securing tabs. 

 

NOTE: 

The WLAN card may have two or three antenna connectors, depending on the type of card you have.

 

NOTICE: 

The card connector is keyed to ensure correct insertion. If you feel resistance, check the connector and realign the card.

 

NOTICE: 

Do not insert a Mobile Broadband network (WWAN) card into the WLAN card connector.

Содержание Latitude D631












































Отзывы: