Dell Latitude D430 Скачать руководство пользователя страница 1

Страница: 1 / 37

Dell™ Latitude™ D430 Service Manual

Notes, Notices, and Cautions

Information in this document is subject to change without notice.

Reproduction in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.

Trademarks used in this text:

Dell

, the

DELL

logo, and

InspironLatitude

are trademarks of Dell

Inc.;

Bluetooth

is a trademark owned by Bluetooth SIG, Inc. and is used by Dell Inc.

under license.

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any
proprietary interest in trademarks and trade names other than its own.

Model PP09S

June 2007 Rev. A00

Internal Card With Bluetooth

Wireless Technology

Memory and Mini-Cards

Display Assembly

Palm Rest

Speaker

Suspend-Switch Sensor Board

System Board

Fan

PC Card/Smart Card Reader

Modem

Wireless Switch

Power Button Assembly

Battery Latches

Pin Assignments for I/O Connectors

Flashing the BIOS

NOTE:

A NOTE indicates important information that helps you make better use of your computer.

NOTICE:

A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.

CAUTION:

A CAUTION indicates a potential for property damage, personal injury, or death.

Содержание Latitude D430






































Результаты поиска

Содержание Latitude D430

Отзывы:

Похожие инструкции для Latitude D430

Бренды по названию

Популярные бренды

Dell Latitude D430, Руководство по обслуживанию

Результаты поиска

Содержание Latitude D430

Отзывы:

Похожие инструкции для Latitude D430

Бренды по названию

Популярные бренды