Dell Latitude 7390 Скачать руководство пользователя страница 65 | Manualshive

Страница: 65 / 82

background image

Option

Description

●

Disabled

This option is enabled by default.

●

Every Day

●

Weekdays

●

Select Days

USB Wake
Support

Does not allow this option.

Lid Switch

Allows this option.

Thermal
Management

Allows this option..

Wireless Radio
Control

Allows you to sense the connection of the system to a wired network and subsequently disable the
selected wireless radios (WLAN and/or WWAN)

Upon disconnection from the wired network, the selected wireless radios is re-enabled. By default none of
the option is enabled. The options are:

●

Control WLAN radio

●

Control WWAN radio

Wake on WLAN

Allows you to enable or disable the feature that powers on the computer from the Off state when
triggered by a LAN signal.

●

Disabled

This option is selected by default.

●

LAN with PXE Boot

●

LAN Only

Peak Shift

Allows you to minimize the AC power consumption during the peak power times of day. After you enable
this option, your system runs only in battery even if the AC is attached.

●

Enable Peak Shift

This option is not selected by default.

Advanced
Battery Charge
Configuration

This option enables you to maximize the battery health. By enabling this option, your system uses the
standard charging algorithm and other techniques, during the non-work hours to improve the battery
health.

●

Enable Advanced Battery Charge Mode

This option is not selected by default.

Primary
Battery Charge
Configuration

Allows you to select the charging mode for the battery. The options are:

●

Adaptive

This option is enabled by default.

●

Standard

Fully charges your battery at a standard rate.

●

ExpressCharge

The battery charges over a shorter period of time using Dell’s fast charging

technology.

●

Primarily AC use

●

Custom

If Custom Charge is selected, you can also configure Custom Charge Start and Custom Charge Stop.

NOTE:

All charging mode may not be available for all the batteries. To enable this option, disable the

Advanced Battery Charge Configuration

option.

POST Behavior

Option

Description

Adapter
Warnings

Allows you to enable or disable the system setup (BIOS) warning messages when you use certain power
adapters.

Enable Adapter Warnings

This option is selected by default.

Numlock Enable

Allows you to enable the Numlock option when the computer boots.

●

Enable Network

This option is enabled by default.

System setup

65

«
...
63
64
65
66
67
...
»

Содержание Latitude 7390



















































































Отзывы:

Нет отзывов

Похожие инструкции для Latitude 7390

Aspire One AOP531h

Бренд: Acer Страницы: 12

AMILO Xi Series

Бренд: Fujitsu Siemens Computers Страницы: 96

Бренд: ANSMANN Страницы: 10

Бренд: Acer Страницы: 87

Бренд: Krüger & Matz Страницы: 25

Бренд: Lenovo Страницы: 84

2384EHU - ThinkPad G40 2384

Бренд: Lenovo Страницы: 164

Бренд: Lenovo Страницы: 34

Бренд: Lenovo Страницы: 4

Бренд: Lenovo Страницы: 218

278182U - IdeaPad Y430 Dual Core T3400 2.16 GHz

Бренд: Lenovo Страницы: 150

Бренд: Lenovo Страницы: 2

Бренд: HP Страницы: 22

Armada 1500c Series

Бренд: HP Страницы: 36

6830s - Compaq Business Notebook

Бренд: HP Страницы: 36

Бренд: HP Страницы: 3

Бренд: HP Страницы: 12

8710p - Compaq Business Notebook

Бренд: HP Страницы: 42

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды