manualshive.com logo in svg

Dell Latitude 5300, Руководство по обслуживанию, Страница: 121 / 123

Поделиться
Скачать
Dell Latitude 5300 Скачать руководство пользователя страница 121

Solid white

 — Power adapter is connected and the battery has more than 5 percent charge.

Amber

 — Computer is running on battery and the battery has less than 5 percent charge.

Off

●

Power adapter is connected and the battery is fully charged.

●

Computer is running on battery and the battery has more than 5 percent charge.

●

Computer is in sleep state, hibernation, or turned off.

The power and battery-status light blinks amber along with beep codes indicating failures.

For example, the power and battery-status light blinks amber two times followed by a pause, and then blinks white three times
followed by a pause. This 2,3 pattern continues until the computer is turned off indicating no memory or RAM is detected.

The following table shows different power and battery-status light patterns and associated problems.

Table 3. LED codes 

Diagnostic light codes

Problem description

2,1

Processor failure

2,2

System board: BIOS or ROM (Read-Only Memory) failure

2,3

No memory or RAM (Random-Access Memory) detected

2,4

Memory or RAM (Random-Access Memory) failure

2,5

Invalid memory installed

2,6

System-board or chipset error

2,7

Display failure

2,8

LCD power rail failure. Replace system board and LCD

3,1

Coin-cell battery failure

3,2

PCI, video card/chip failure

3,3

Recovery image not found

3,4

Recovery image found but invalid

3,5

Power-rail failure

3,6

System BIOS Flash incomplete

3,7

Management Engine (ME) error

Camera status light:

 Indicates whether the camera is in use.

●

Solid white — Camera is in use.

●

Off — Camera is not in use.

Caps Lock status light:

 Indicates whether Caps Lock is enabled or disabled.

●

Solid white — Caps Lock enabled.

●

Off — Caps Lock disabled.

WiFi power cycle

About this task

If your computer is unable to access the internet due to WiFi connectivity issues a WiFi power cycle procedure may be
performed. The following procedure provides the instructions on how to conduct a WiFi power cycle:

NOTE:

 Some ISPs (Internet Service Providers) provide a modem/router combo device.

Steps

1. Turn off your computer.

Troubleshooting

121

Содержание Latitude 5300




























































































































Отзывы:

Нет отзывов