Dell Inspiron 3782 Скачать руководство пользователя страница 71

Страница: 71 / 99

Removing the system board

NOTE:

Before working inside your computer, read the safety information that shipped with your computer and follow

the steps in

Before working inside your computer

. After working inside your computer, follow the instructions in

After

working inside your computer

. For more safety best practices, see the Regulatory Compliance home page at

www.dell.com/regulatory_compliance

NOTE:

Your computer’s Service Tag is stored in the system board. You must enter the Service Tag in the BIOS setup

program after you replace the system board.

NOTE:

Replacing the system board removes any changes you have made to the BIOS using the BIOS setup program. You

must make the appropriate changes again after you replace the system board.

NOTE:

Before disconnecting the cables from the system board, note the location of the connectors so that you can

reconnect the cables correctly after you replace the system board.

Prerequisites

1. Remove the

2. Remove the

3. Remove the

4. Remove the

5. Remove the

6. Remove the

7. Remove the

Removing the system board

Содержание Inspiron 3782




































































































Результаты поиска

Содержание Inspiron 3782

Отзывы:

Похожие инструкции для Inspiron 3782

Бренды по названию

Популярные бренды

Dell Inspiron 3782, Руководство по обслуживанию

Результаты поиска

Содержание Inspiron 3782

Отзывы:

Похожие инструкции для Inspiron 3782

Бренды по названию

Популярные бренды