Dell Inspiron 3782 Скачать руководство пользователя страница 29

Страница: 29 / 99

Removing the memory modules

NOTE:

Before working inside your computer, read the safety information that shipped with your computer and follow

the steps in

Before working inside your computer

. After working inside your computer, follow the instructions in

After

working inside your computer

. For more safety best practices, see the Regulatory Compliance home page at

www.dell.com/regulatory_compliance

Prerequisites

1. Remove the

optical drive

2. Remove the

base cover

Procedure

1. Locate the memory module on your computer.

2. Use your fingertips to carefully spread apart the securing-clips on each end of the memory-module slot until the memory module pops

up.

3. Remove the memory module from the memory-module slot.

Removing the memory modules

Содержание Inspiron 3782




































































































Результаты поиска

Содержание Inspiron 3782

Отзывы:

Бренды по названию

Популярные бренды

Dell Inspiron 3782, Руководство по обслуживанию

Результаты поиска

Содержание Inspiron 3782

Отзывы:

Бренды по названию

Популярные бренды