manualshive.com logo in svg

Dell Inspiron 17 7000 Series, Руководство по обслуживанию

Поделиться
Скачать
Dell Inspiron 17 7000 Series Скачать руководство пользователя страница 106

Replacing the sensor board

WARNING: Before working inside your computer, read the safety 
information that shipped with your computer and follow the steps in 

Before 

working inside your computer

. After working inside your computer, follow 

the instructions in 

After working inside your computer

. For more safety best 

practices, see the Regulatory Compliance home page at 

www.dell.com/

regulatory_compliance

.

 

Procedure

1 

Align the sensor board on the display-panel assembly and snap the sensor board 
in place.

2 

Slide the sensor-board cable into the connector on sensor board and press down 
the latch to secure the cable.

3 

Adhere the tape that secures the sensor-board cable to the sensor board.

4 

Replace the screw (M2x2 Big Head) that secures the sensor board to the 
display-panel assembly.

Post-requisites

1 

Follow the procedure from step 6 to step 8 in “

Replacing the display panel

”.

2 

Replace the 

display assembly

.

3 

Replace the 

wireless card

.

4 

Replace the 

battery

.

5 

Replace the 

base cover

.

106

Содержание Inspiron 17 7000 Series





































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды