Dell Inspiron 1318 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 46

background image

Back to Contents Page

Coin-Cell Battery

Dell™ Inspiron™ 1318 Service Manual

Removing the Coin-Cell Battery

Replacing the Coin-Cell Battery

Removing the Coin-Cell Battery

1.

Follow the procedures in

Before You Begin

2.

Remove the module cover (see

3.

The battery is glued to the computer, use a plastic scribe to pry the coin-cell battery from the slot.

4.

Disconnect the coin-cell battery cable from the system board connector.

Replacing the Coin-Cell Battery

1.

Connect the coin-cell battery cable to the system board connector.

2.

Peel off the adhesive on the coin-cell battery and adhere it to the system board.

3.

Replace the module cover (see

4.

Slide the battery into the battery bay, until it clicks into place.

Back to Contents Page

CAUTION:

Before you begin any of the procedures in this section, follow the safety instructions shipped with your system.

NOTICE:

To avoid electrostatic discharge, ground yourself by using a wrist grounding strap or by periodically touching an unpainted metal surface (such

as a connector on the back of the computer).

NOTICE:

To help prevent damage to the system board, you must remove the battery from the battery bay before you begin working inside the

computer.

1

coin-cell battery cable connector

2

coin-cell battery

«
...
11
12
13
14
15
...
»

Содержание Inspiron 1318















































Отзывы:

Нет отзывов

Похожие инструкции для Inspiron 1318

Бренд: Raven Страницы: 34

Бренд: Raven Страницы: 8

Literail Workstation 4 Person

Бренд: Jason.L Страницы: 4

Бренд: Digital Equipment Страницы: 96

Бренд: Gateway Страницы: 50

Бренд: Mitsubishi Electric Страницы: 44

Бренд: Mitsubishi Electric Страницы: 40

Бренд: IBM Страницы: 52

Бренд: Toshiba Страницы: 5

Бренд: Toshiba Страницы: 5

Бренд: Toshiba Страницы: 5

Бренд: Toshiba Страницы: 5

Бренд: Toshiba Страницы: 5

Бренд: Toshiba Страницы: 4

Бренд: Toshiba Страницы: 1

Бренд: Toshiba Страницы: 4

Бренд: Toshiba Страницы: 5

Бренд: Toshiba Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды