Dell FS7500 Скачать руководство пользователя | Manualshive

Страница: 10 / 88

background image

•

Use care when moving and opening the cartons. Leave the components packaged until you are ready to
install them.

•

Place the components in a protected area that has adequate airflow and is free of humidity, flammable gas,
and corrosion.

•

You need at least two people to install the hardware. Use proper lifting and carrying techniques when
unpacking and moving the components.

•

Make sure each FS7500 Controller is fully grounded at all times to prevent damage from electrostatic
discharge.

•

When handling an FS7500 Controller, use the electrostatic wrist guard shipped with the controller or a
similar form of protection. See

Hardware Protection on page 4

•

Hold the hardware level with the rack when you install it.

Warning:

The BPS contains LETHAL VOLTAGES. All repairs and service should be performed by
AUTHORIZED SERVICE PERSONNEL ONLY. There are no customer replaceable parts inside
the BPS.

•

Unpacking the BPS in a low-temperature environment might cause condensation to occur in and on the
chassis. This could cause electric shock. Do not install the chassis and power modules until both the inside
and outside of the chassis are dry.

•

Always connect the BPS battery packs to the chassis before connecting the input power cables.

•

Both the 120V (LV) and the 230V (HV) power modules have IEC 320 C13 output receptacles. Make sure to
use power cables rated for the correct input power source rating. The rating is on a label next to the input
connector on the power module rear panel.

Hardware Protection

When not installed in a rack, an FS7500 Controller must be in its original packaging or placed on a sturdy
surface that is protected from electrostatic discharge.

When handling an FS7500 Controller, make sure you use the electrostatic wrist strap that is shipped with the
controller or a similar form of protection.

Using an Electrostatic Wrist Strap

You must protect sensitive hardware from electrostatic discharge.

To use an electrostatic wrist strap:

1. Connect the steel snap on the coil cord to the stud on the elastic band. See

.

4

EqualLogic FS7500 Installation and Setup

1 Before You Begin

«
...
8
9
10
11
12
...
»

Содержание FS7500

























































































Отзывы:

Нет отзывов

Похожие инструкции для FS7500

Бренд: Samsung Страницы: 2

Бренд: Samsung Страницы: 31

Бренд: Samsung Страницы: 15

Бренд: Harman Kardon Страницы: 66

Module NI PXI-8250

Бренд: National Instruments Страницы: 39

ROADRECORDER 8000

Бренд: Safety Vision Страницы: 40

Firebox SOHO 6 Wireless

Бренд: Watchguard Страницы: 8

HHM Series HHM2411

Бренд: TDK Страницы: 2

Бренд: axing Страницы: 4

Бренд: AMX Страницы: 1

Бренд: Air Live Страницы: 2

Бренд: Digital Equipment Страницы: 90

Бренд: Rane Страницы: 6

Бренд: ekwb Страницы: 16

Бренд: Paradyne Страницы: 46

NetStructure ZT 5085

Бренд: Intel Страницы: 106

Бренд: ATCOM Страницы: 18

Diamond Systems DS-MPE-CAN2L

Бренд: Fortec Star Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды