Dell EMC VNXe Series Скачать руководство пользователя страница 44

Страница: 44 / 52

EMC VNXe3100 Hardware Information Guide

Overview

6-Gb/s SAS port LEDs and port direction (input or output) —

shows the LCC

6-Gb/s SAS port LED—a bi-color (blue/green) LED below the connector, either left or
right—that indicates the link of the SAS port.

Figure 28

also shows a double black circle

(or dot)

symbol (for input) or a double black diamond

symbol (for output).

Figure 28 DAE LCC 6-Gb/s SAS port LED

Table 21

describes the DAE LCC 6-Gb/s SAS port LED.

LCC enclosure ID (enclosure address) and bus ID

On the rear of the LCC (A and B), an LCC enclosure ID indicator is provided. This ID
indicator is a seven-segment LED for displaying decimal numbers. The LCC enclosure ID
appears on both LCCs (A and B) which is the same ID number.

Figure 29

shows the

enclosure ID is set at installation.

Each LCC includes a bus (loop) identification indicator. This indicator is a seven-segment
LED for displaying decimal numbers.

Figure 29

shows the SP initializes the bus ID when

the operating system is loaded.

Figure 29 Example of LCC loop bus ID and enclosure ID

6Gb SAS

VNX-000087

Table 21 DAE LCC 6-Gb/s SAS port LED

LED

Color

State

Description

Link

Blue

All lanes are running at 6 GB/s

Green

One or more lanes running at 1.5 or 3 Gb/s

Alternating

Blue/Green

Blinking

Port is being marked by the host

—

Off

Not connected

6Gb SAS

Enclosure ID

Loop bus ID

VNX-000081

Содержание EMC VNXe Series





















































Результаты поиска

Содержание EMC VNXe Series

Отзывы:

Бренды по названию

Популярные бренды

Dell EMC VNXe Series, Руководство по аппаратным средствам

Результаты поиска

Содержание EMC VNXe Series

Отзывы:

Бренды по названию

Популярные бренды