Dell EMC PowerEdge T440 Скачать руководство пользователя страница 8

Страница: 8 / 150

Dell EMC PowerEdge T440 overview

The PowerEdge T440 is a dual-socket, 5U rackable tower server that supports up to:

•

Two Intel Xeon Scalable Processor Family processors

•

Sixteen DIMM slots supporting up to a total of 16 x 64 GB = 1024GB of memory

•

Five PCIe Gen 3 expansion cards

•

4 or 8 x 3.5 inch SAS/SATA-hard drive or SSD, or 16 x 2.5 inch SAS/SATA drive bays (up to 12 Gbps SAS and 6 Gbps SATA)

•

Redundant power supply units (PSUs)

•

Cabled power supply units (PSUs)

Topics:

•

Supported configurations for the PowerEdge T440 system

•

Front view of the system

•

Back view of the system

•

Locating the Service Tag of your system

Supported configurations for the PowerEdge T440

system

The Dell EMC PowerEdge T440 system supports the following configurations:

Installation and Service Manual
Dell EMC PowerEdge T440 overview

Содержание EMC PowerEdge T440























































































































































Результаты поиска

Содержание EMC PowerEdge T440

Отзывы:

Похожие инструкции для EMC PowerEdge T440

Бренды по названию

Популярные бренды

Dell EMC PowerEdge T440, Руководство пользователя

Результаты поиска

Содержание EMC PowerEdge T440

Отзывы:

Похожие инструкции для EMC PowerEdge T440

Бренды по названию

Популярные бренды