Dell EMC PowerEdge T440 Скачать руководство пользователя

Страница: 70 / 156

Figure 19. Installing the front bezel

System feet

The system feet provide stability to the system in the tower mode.

Removing the system feet

Prerequisites

NOTE:

It is recommended that you remove the system feet only when you are converting the system from the tower mode to the

rack mode, or when you are replacing the system feet with the wheel assembly.

Follow the safety guidelines listed in

Safety instructions

Place the system on its side on a flat, stable surface.

Rotate the system feet inward.

Step

Using the Phillips #2 screwdriver, remove the screw that secures the foot to the base of the system.

a Repeat the above step for the 3 remaining feet.

Dell EMC PowerEdge T440 Installation and Service Manual
Installing and removing system components

Содержание EMC PowerEdge T440





























































































































































Результаты поиска

Содержание EMC PowerEdge T440

Отзывы:

Похожие инструкции для EMC PowerEdge T440

Бренды по названию

Популярные бренды

Dell EMC PowerEdge T440, Инструкция по установке и обслуживанию

Результаты поиска

Содержание EMC PowerEdge T440

Отзывы:

Похожие инструкции для EMC PowerEdge T440

Бренды по названию

Популярные бренды