Dell DF10MXL Скачать руководство пользователя страница 34

Страница: 34 / 36

Technical Specifications

Technical Specifications

The MXL 10/40GbE Switch is an I/O module and installed with Server

(model: PowerEdge M1000e) for communication.

NOTE:

The product must be operated at an ambient temperature of 50°C.

CAUTION:

A Lithium Battery Caution: There is a danger of explosion if the battery

is incorrectly replaced.

Replace only with same or equivalent type. Dispose batteries according to

manufacturer's instructions.

Chassis Physical Design

Environmental Parameters

Parameter

Specifications

Height

1.32 inches (33.45 mm)

Width

10.81 inches (274.75 mm)

Depth

12.17 inches (309.24 mm)

Parameter

Specifications

Operating temperature

32° to 104°F (0° to 40°C)

Operating humidity

10 to 85% (RH), non-condensing

Storage temperature

–40° to 158°F (–40° to 70°C)

Storage humidity

5 to 95% (RH), non-condensing

Maximum thermal output

419.7 BTU/hr

Содержание DF10MXL





































Результаты поиска

Содержание DF10MXL

Отзывы:

Бренды по названию

Популярные бренды

Dell DF10MXL, Руководство по началу работы

Результаты поиска

Содержание DF10MXL

Отзывы:

Бренды по названию

Популярные бренды