background image

Before You Begin: Dell Latitude D800 Service Manual

Back to Contents Page

 

Before You Begin 

Dell™ Latitude™ D800 Service Manual

  

Preparing to Work Inside the Computer

  

Recommended Tools

  

Computer Orientation

  

Screw Identification

Preparing to Work Inside the Computer

 

CAUTION: 

Only a certified service technician should perform repairs on your computer. 

Damage due to servicing that is not authorized by Dell is not covered by your warranty. 

Read and follow applicable instructions in the safety instructions in the 

System 

Information Guide

 that came with the computer.

 

CAUTION: 

To prevent static damage to components inside your computer, discharge 

static electricity from your body before you touch any of your computer's electronic 

components. You can do so by touching an unpainted metal surface.

 

CAUTION: 

Handle components and cards with care. Do not touch the components or 

contacts on a card. Hold a card by its edges or by its metal mounting bracket. Hold a 

component such as a microprocessor by its edges, not by its pins.

NOTICE: 

To avoid damaging the computer, perform the following steps before you begin working 

inside the computer. 

1.  Ensure that the work surface is flat and clean to prevent scratching the computer cover. 

2.  Save any work in progress and exit all open programs. 

3.  Turn off the computer and all attached devices. 

NOTE: 

Ensure that the computer is off and not in a power management mode. If you cannot shut 

down the computer using the computer operating system, press and hold the power button for 4 

seconds. 

4.  If the computer is connected to a docking station, undock it. 

5.  Disconnect the computer from the electrical outlet. 

6.  To avoid possible damage to the system board, wait 10 to 20 seconds and then disconnect any 

file:///I|/SERVICE%20MANUALS/DELL%20MANUALS/L...titude/D800/D800%20SERVICE%20MANUAL/begin.htm (1 of 7)6/21/2004 2:16:50 AM

Содержание D800 - Latitude 15.4" Notebook















































































Отзывы: