background image

Table 17. Dimensions of the VxRail D Series appliance 

Xa

Xb

Y

Za (with

bezel)

Za (without

bezel)

Zb

Zc

482.6 mm

(19 inches)

434.0 mm

(17.08 inches)

42.8 mm

(1.68 inches)

63.15 mm

(2.46 inches)

33.9 mm

(1.32 inches)

514.35 mm

(20.06 inches)

547.4 mm

(21.35 inches)

Chassis weight

Table 18. Chassis weight 

System

Maximum weight (with all drives/SSDs)

8 x 2.5 inch drive system

13.00 Kg (28 lb)

Processor specifications

The VxRail D Series system supports up to two Intel Xeon Processor Scalable Family processors.

PSU specifications

The VxRail D Series system supports the following AC power supplies unit (PSU):

Table 19. PSU specifications 

PSU

Class

Heat dissipation

(maximum)

Frequency

Voltage

550 W AC

Platinum

2108 BTU/hr

50/60 Hz 

115–230 V AC

NOTE:

 Heat dissipation is calculated using the PSU wattage rating.

NOTE:

 This system is also designed to connect to the IT power systems with a phase-to-phase voltage not exceeding 230

V for an AC power supply unit.

System battery specifications

The VxRail D Series system supports CR 2032 3.0-V lithium coin cell system battery.

Expansion bus specifications

The VxRail D Series system supports PCI express (PCIe) generation three expansion cards, which must be installed on the
system board using expansion card risers. The D Series system supports four types of expansion card risers.

Table 20. PCIe expansion card riser configurations - 1 CPU 

Expansion card riser PCIe slots on the

riser

Height

Length

Link

LOM riser

Slot 1

Unique to Dell

Unique to Dell

x8

Right riser

Slot 2

Full Height

Half Length

x16

Internal riser

Slot-integrated

Platform specific

Platform specific

x8

20

Technical specifications

Содержание D560


































Отзывы: