background image

Next steps

1. Install the 

left-side cover

.

2. Follow the procedure in 

After working inside your computer

.

Memory modules

Removing the memory modules

Prerequisites

1. Follow the procedure in 

Before working inside your computer

.

2. Remove the 

left-side cover

.

About this task

The following images indicate the location of the memory modules and provides a visual representation of the removal procedure.

Steps

1. Lay the chassis on the right side.
2. Use your fingertips to carefully spread apart the securing-clips on each end of the memory-module slot.
3. Grasp the memory module near the securing clip, and then gently ease the memory module out of the memory-module slot.

NOTE: 

Repeat step 2 to step 4 to remove any other memory modules installed in your computer.

NOTE: 

Note the slot and the orientation of the memory module in order to replace it in the correct slot.

NOTE: 

If the memory module is difficult to remove, gently ease the memory module back and forth to remove it from 

the slot.

Disassembly and reassembly

29

Содержание D28M































































































Отзывы: