background image

Installing the internal hard-drive cage

Prerequisites

If you are replacing a component, remove the existing component before performing the installation procedure.

About this task

The following images indicate the location of the internal hard-drive cage and provide a visual representation of the installation
procedure.

Steps

1. Slide and insert the hard-drive cage into the slot on the chassis.
2. Install the four (#6-32) screws to secure the hard-drive cage to the chassis.
3. Connect the SATA power-cables and SATA data-cables to the connectors on the system board.

Next steps

1. Install the 

3.5-inch hard-drive assembly

.

2. Install the 

2.5-inch hard-drive assembly

.

3. Install the 

air shroud

.

4. Install the 

side cover

.

5. Follow the procedure in 

After working inside your computer

.

Voltage-regulator heat sink

Removing the voltage-regulator heat sink - Location 1

Prerequisites

1. Follow the procedure in 

Before working inside your computer

.

WARNING:

 The heat sink may become hot during normal operation. Allow sufficient time for the heat sink to

cool before you touch it.

CAUTION:

 For maximum cooling of the processor, do not touch the heat transfer areas on the heat sink. The

oils in your skin can reduce the heat transfer capability of the thermal grease.

80

Removing and installing components

Содержание D03T
























































































































Отзывы: