Dell Alienware 13 R3 Скачать руководство пользователя

Страница: 57 / 78

Removing the camera cable

NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow the steps
in

Before working inside your computer

. After working inside your computer, follow the instructions in

After working inside your

computer

. For more safety best practices, see the Regulatory Compliance home page at

www.dell.com/regulatory_compliance

Topics:

•

Prerequisites

•

Procedure

Prerequisites

NOTE: These instructions are applicable only for laptops with a non-touch screen display.

1. Remove the

2. Remove the

3. Remove the

4. Remove the

5. Remove the

6. Remove the

7. Remove the

8. Remove the

9. Remove the

10. Remove the

11. Remove the

12. Remove the

13. Remove the

14. Remove the

Procedure

1. Peel the tape that secures the camera cable to the camera module and disconnect the camera cable from the camera module.
2. Note the camera cable routing and remove the cable from the routing guides on the display back-cover and antenna assembly.

Содержание Alienware 13 R3















































































Результаты поиска

Содержание Alienware 13 R3

Отзывы:

Похожие инструкции для Alienware 13 R3

Бренды по названию

Популярные бренды

Dell Alienware 13 R3, Руководство по обслуживанию

Результаты поиска

Содержание Alienware 13 R3

Отзывы:

Похожие инструкции для Alienware 13 R3

Бренды по названию

Популярные бренды