Dell Alienware 13 R3 Скачать руководство пользователя страница 74

Страница: 74 / 78

Table 5. Security tab

(continued)

Security

Default: Permitted

Computrace

Enable or disable the BIOS module interface of the optional

Computrace Service from Absolute Software.

Firmware TPM

UEFI Capsule Firmware Updates

Enable or disable BIOS updates through UEFI capsule update

packages.

Table 6. Boot tab

Boot

Boot List Option

Displays the available boot options.

File Browser Add Boot Option

Allows to add the boot options.

File Browser Del Boot Option

Allows to delete the boot options

Secure Boot

Enable or disable the secure boot feature.

Legacy Option ROMs

Enable or disable the Legacy Option ROMs.

Boot Option Priorities

Displays the boot sequence.

Boot Option #1

Displays the available first boot option.

Boot Option #2

Displays the available second boot option.

Boot Option #3

Displays the available third boot option.

Table 7. Exit tab

Exit

Save Changes and Reset

Allows you to exit system setup and save your changes.

Discard Changes and Reset

Allows you to exit system setup and load previous values for

all system setup options.

Restore Defaults

Allows you to restore default values for all system setup

options.

Discard Changes

Allows you to load previous values for all system setup

options.

Save Changes

Allows you to save the changes for all system setup options.

Clearing BIOS (System Setup) and System passwords

Contact Dell technical support to clear the forgotten passwords. For more information, see

www.dell.com/contactdell

Clearing CMOS settings

1. Remove the

2. Remove the

3. Remove the

4. Remove the

5. Remove the

6. Remove the

7. Remove the

8. Wait for one minute.

Содержание Alienware 13 R3















































































Результаты поиска

Содержание Alienware 13 R3

Отзывы:

Бренды по названию

Популярные бренды

Dell Alienware 13 R3, Руководство по обслуживанию

Результаты поиска

Содержание Alienware 13 R3

Отзывы:

Бренды по названию

Популярные бренды