manualshive.com logo in svg

Dell 5000 Series, Руководство по обслуживанию

Поделиться
Скачать
Dell 5000 Series Скачать руководство пользователя страница 27

15

Replacing the base frame

WARNING: Before working inside your computer, read the safety information that shipped with 

your computer and follow the steps in 

Before working inside your computer

. After working inside 

your computer, follow the instructions in 

After working inside your computer

. For more safety 

best practices, see the Regulatory Compliance home page at www.dell.com/

regulatory_compliance. 

 

Procedure

1.

Place the base frame on the bottom cover.

2.

Connect the Dip Switch board cable and status-light board cable from the system board

3.

Connect the wireless card cables and mobile broadband card cables from the routing guides.

4.

Replace the system grounding port screw.

5.

Turn the system over.

6.

Replace the screws that secures the bottom cover to the base frame.

7.

Turn the system right side up.

Post-requisites

1.

Replace the 

mobile broadband card

.

2.

Replace the 

wireless card

.

3.

Replace the 

solid-state drive

.

4.

Replace the 

top cover

.

27

Содержание 5000 Series









































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды