Dell EMC PowerEdge R7525 Скачать руководство пользователя страница 64

Страница: 64 / 209

Figure 34. Removing the cooling fan cage assembly

Next steps

Install the cooling fan cage assembly

Installing the cooling fan cage assembly

Prerequisites

1. Follow the safety guidelines listed in the

Safety instructions

on page 46.

CAUTION:

Ensure that the cables inside the system are correctly installed and retained by the cable retention

bracket before installing the cooling fan cage assembly. Incorrectly installed cables may get damaged.

2. Follow the procedure listed in

Before working inside your system

on page 47.

3. If installed,

remove the air shroud

Steps

1. Align the guide rails on the cooling fan cage assembly with the standoffs on the system.
2. Lower the cooling fan cage assembly into the system until the cooling fan cage connectors engage with the connectors on the system

board.

3. Press the release levers to lock the cooling fan cage assembly into the system.

Installing and removing system components

Содержание PowerEdge R7525


















































































































































































































Результаты поиска

Содержание PowerEdge R7525

Отзывы:

Dell EMC PowerEdge R7525, Инструкция по установке и обслуживанию, Страница: 64 / 209

Результаты поиска

Содержание PowerEdge R7525

Отзывы: