Dell EMC PowerEdge R7525 Скачать руководство пользователя страница 168

Страница: 168 / 209

Next steps

Install the system board

Installing the system board

Prerequisites

NOTE:

Before replacing the system board, replace the old iDRAC MAC address label in the Information tag with the

iDRAC MAC address label of the replacement system board

1. Follow the safety guidelines listed in the

Safety instructions

on page 46.

2. Follow the procedure listed in

Before working inside your system

on page 47.

3. If you are replacing the system board, remove all the components that are listed in the removing the system board section.

Steps

1. Unpack the new system board assembly.

CAUTION:

Do not lift the system board by holding a memory module, processor, or other components.

CAUTION:

Take care not to damage the system identification button while placing the system board into the chassis.

2. Holding the system board holder and plunger, lower the system board into the system.
3. Slide the system board towards the rear of the chassis until the connectors are firmly seated in the slots.

Figure 128. Installing the system board

4. Using the Phillips #2 screwdriver secure the system board to the chassis with screws

168

Installing and removing system components

Содержание PowerEdge R7525


















































































































































































































Результаты поиска

Содержание PowerEdge R7525

Отзывы:

Dell EMC PowerEdge R7525, Инструкция по установке и обслуживанию, Страница: 168 / 209

Результаты поиска

Содержание PowerEdge R7525

Отзывы: