Dell EMC PowerEdge R7525 Скачать руководство пользователя страница 150

Страница: 150 / 209

Figure 109. Removing the MicroSD card

Next steps

Replace the MicroSD cards

Installing the MicroSD card

Prerequisites

1. Follow the safety guidelines listed in the

Safety instructions

on page 46.

2. Follow the procedure listed in

Before working inside your system

on page 47.

NOTE:

To use an MicroSD card with your system, ensure that the Internal SD Card Port is enabled in System Setup.

NOTE:

Ensure that you install the MicroSD cards into the same slots based on the labels you had marked on the cards

during removal.

Steps

1. Locate the MicroSD card slot on the IDSDM module. Orient the MicroSD card appropriately and insert the contact-pin end of the card

into the slot. To locate IDSDM, see the

System board jumpers and connectors

section.

NOTE:

The slot is keyed to ensure correct insertion of the card.

2. Press the card into the slot to lock it into place.

150

Installing and removing system components

Содержание PowerEdge R7525


















































































































































































































Результаты поиска

Содержание PowerEdge R7525

Отзывы:

Dell EMC PowerEdge R7525, Инструкция по установке и обслуживанию, Страница: 150 / 209

Результаты поиска

Содержание PowerEdge R7525

Отзывы: